A dehumidifier and air mover drying a bedroom subfloor after the carpet and pad were pulled back

Water Damage Restoration Cost in Bellingham, WA

National figures put most water damage restoration jobs at about $1,400 to $6,400, with an average near $3,800 (HomeAdvisor, 2025 national data). Per square foot, national figures run about $3 to $7.50, depending on how dirty the water is (Angi). We found no reliable Bellingham or Washington average, so every figure on this page is national.

Your own bill depends on four things. One is how much of the home is wet. Another is whether the water is clean, gray or sewage. The others are how much material has to come out and how many days the drying equipment runs.

Want a number for your home? Call (360) 555-0123 to be connected with a local restoration company. Ask for a written estimate before any non-emergency work starts.

Call now(360) 555-0123 Calls answered 24/7Nights, weekends, holidays
  • Connected fast
  • Bellingham and Whatcom County
  • Calls answered 24/7Nights, weekends and holidays
  • Connected fastStraight to a local restoration company
  • All of Whatcom CountyBellingham, Ferndale, Lynden, Blaine and more
  • Water, sewage and moldBurst pipes, floods and backups

How much does water damage restoration cost? National ranges by job type

These national ranges come from consumer cost sites. They're a starting point, not a quote.

Job type National range Source
Typical water damage restoration job About $1,400–$6,400; average near $3,800 HomeAdvisor
Clean water (Category 1), per sq ft $3–$4 Angi
Gray water (Category 2), per sq ft $4–$6.50 Angi
Sewage or floodwater (Category 3), per sq ft $7–$7.50, not counting replacing what was ruined Angi
Flooded basement cleanup About $2,000–$7,000; average about $4,000 Angi
Sewage cleanup About $2,000–$15,000+; $7–$15+ per sq ft HomeGuide
Crawl space water damage Minor: $250–$4,000. Standing water: $2,000–$10,000 Angi
Mold remediation About $1,200–$3,750 Angi

Ask whether any figure includes rebuilding. Drying out the house and putting back drywall, flooring and trim are often priced as separate jobs.

How much does water damage restoration cost per square foot?

Nationally, about $3 to $7.50 per square foot (Angi). Clean water sits at the low end and sewage at the high end. Two rooms the same size can cost very different amounts if one has wet hardwood or water inside the walls.

How much does flooded basement cleanup cost?

Nationally, most flooded basement cleanups run about $2,000 to $7,000 (Angi, 2026 data). A basement flooded by a sewer backup or river water costs more than one flooded by a burst pipe. That's because carpet, drywall and insulation the dirty water touched have to be removed. See flooded basement cleanup.

How much does water damage from a burst pipe cost to repair?

Expect two bills. A plumber fixes the pipe. A restoration company dries the house and removes what can't be saved. Burst-pipe water is usually clean at first, so the per-square-foot price tends to sit at the low end if drying starts fast. See burst and frozen pipe water damage.

What makes a water damage job cost more?

The price follows the work.

Wet carpet peeled back to show the soaked pad, tack strip and a damp subfloor
What changes the price Why it costs more
How much is wet More square feet, rooms or floors means more labor and more equipment
Water category Gray water and sewage need protective gear, cleaning, disinfecting and more removal
What's wet Hardwood, wall cavities and concrete take longer to dry than carpet on a wood subfloor
Time before drying starts Water that sits gets dirtier, so a gray-water job can become a sewage-grade job. EPA says to dry wet materials within 24 to 48 hours to prevent mold
Equipment days Air movers and dehumidifiers are billed per unit, per day
What has to come out Removal and disposal are billed by quantity: square feet of drywall, carpet, pad, cabinets
Access Crawl spaces and finished basements take longer to work in
After-hours call-out Nights and weekends can carry an emergency response charge

Older homes can add steps. In ZIP 98225, 57% of homes were built before 1980 (US Census ACS 2020–2024). In Whatcom County, Northwest Clean Air Agency rules require checking for asbestos before renovation or demolition. That check is usually a survey by a certified inspector, and it shows up as its own line item. Paid work that disturbs paint in homes built before 1978 falls under Washington's lead-safe work rules.

Permits can add cost on the rebuild. In Bellingham, finish work like paint and carpet doesn't need a building permit. Replacing a concealed pipe or cutting away part of a wall does (City of Bellingham).

Why are dehumidifiers and air movers billed per day?

Drying equipment is billed per machine, per day, because that's how the work is measured. Air movers speed evaporation from wet materials. Dehumidifiers pull that moisture out of the air. The number of machines should drop as rooms read dry.

Air movers and a dehumidifier set up to dry an opened wall

Ask three questions about any equipment line:

  • How many machines, and why that many?
  • Which days did each one run, and in which room?
  • When was each one removed, and do the moisture readings back that up?

Some companies bill a partial day as a full day. Ask how the company counts them before work starts. See structural drying.

The 7 line items to check on a water damage estimate

The charges on a water damage estimate usually fall into these seven groups.

Water-damaged drywall, rolled carpet and trash bags piled at the curb for disposal
  1. Emergency response and assessment. After-hours call-out and moisture mapping. A trip fee shouldn't be billed as a full inspection.
  2. Water extraction. Priced by how much water there is, the flooring and access, and whether the water is contaminated.
  3. Removal and disposal. Each material should have its own quantity, plus a reason it couldn't be dried in place.
  4. Drying equipment. Per unit, per day. The count should match the moisture readings.
  5. Containment, cleaning and safety. Floor protection, plastic barriers, HEPA air filtering, antimicrobial treatment and protective gear.
  6. Monitoring and documentation. Daily moisture readings, temperature and humidity logs, and photos.
  7. Repairs and rebuild. Often a separate estimate, sometimes from a different company.

Also ask whether the total includes overhead and profit, sales tax, permits, storage and moving your belongings.

Why are two water damage estimates for the same room so different?

Because they price different work. One estimate may include containment, more equipment days or removing drywall. Another may leave those out and add them later. Compare the line items and quantities, not just the totals.

How do I check a water damage estimate for overcharges?

Match every line to a photo or a moisture reading. Then look for these red flags:

  • Equipment billed after it was picked up
  • The same labor billed twice
  • Equipment running in rooms that were never wet
  • Quantities that don't match the moisture map or photos
  • An invoice that isn't itemized
  • Fees for dispatch, setup or after-hours work that nobody mentioned up front

At the end, ask for the drying record: the first moisture map, daily logs, equipment dates and final readings. Your insurer may ask for the same record.

One 2026 complaint against a Washington restoration franchise shows how this goes wrong. The homeowner got an estimate of about $8,900. The final bills came to about $10,100. Dehumidifier days rose from 24 to 34, and air mover days from 60 to 102 (BBB complaint, 2026). The homeowner asked for the records behind the added days. That complaint is an allegation, but the records request is the right move.

Got an estimate you're not sure about? Compare it with the seven line items above, and ask the company to explain any line you don't follow.

How insurance prices the job: Xactimate, deductibles and sublimits

What is Xactimate?

A moisture meter against damp drywall, the kind of reading that goes into the claim record

Xactimate is estimating software widely used by insurers to price water damage jobs. Its price lists are set by area, down to sales tax by ZIP code. General prices are updated monthly (Xactware). Your adjuster will likely compare the restoration company's bill against an Xactimate estimate for your area.

What does my deductible mean for a water damage claim?

Your deductible is the part of a covered loss you pay before insurance pays. If the whole job costs less than your deductible, insurance pays nothing. That's why some people pay for small jobs themselves.

What is a water damage sublimit?

A sublimit is a smaller cap inside your policy for one kind of loss. Some insurers in Washington have considered optional water damage sublimits. The state's example was a $10,000 cap on a $500,000 policy (WA OIC, 2024). Check your declarations page for one before work starts.

What you may still owe

Even with a covered claim, you may owe:

  • Your deductible.
  • Anything above a sublimit or your policy limit.
  • Water from a source your policy excludes. Most policies don't cover gradual leaks or groundwater seeping in (WA OIC). Flood needs a separate policy, and sewer backup needs an endorsement (WA OIC homeowner guide).
  • The gap between the bill and what the insurer approves. In one Utah case, a homeowner got a bill of nearly $8,500. The insurer said the cleanup should have cost no more than about $5,300, and the company billed her for the rest (KUTV, 2019).
  • Upgrades you choose during the rebuild.

See does insurance cover water damage in Washington and insurance claim help.

Do I have to use the company my insurance sends?

No. Your insurer may suggest preferred contractors, but in Washington you have the right to pick your own (WA OIC). Restoration companies work with your insurer's adjuster; you choose the company.

Paying out of pocket

Can you negotiate an out-of-pocket restoration price?

A tank water heater leaking across a garage floor

Yes, you can ask. Get a written estimate, ask how many machines will run and for how long, and ask what happens if drying finishes early. Don't hold up the emergency drying to collect bids, though. EPA says to dry wet materials within 24 to 48 hours to prevent mold (EPA). Collect bids for the rebuild instead, where a few days' wait costs less.

Is water mitigation or water restoration more expensive?

It depends on how much was removed. Mitigation is the emergency part: removing water and drying the building. Restoration (the rebuild) puts back what was removed. A small leak may cost more to dry than to repair. A sewer backup that took out a whole finished basement usually costs more to rebuild.

How to protect yourself before you sign

After big storms, Washington L&I warns about unregistered contractors. It also warns about uninvited "contractors" who take a deposit and don't finish the job (WA L&I).

  • Check L&I registration on L&I Verify before you pay anything.
  • Read the work authorization. Ask whether it includes an assignment of benefits. That form can let a contractor negotiate and settle the claim directly with your insurer. The WA OIC suggests talking to your agent first. Ask whether any form is an assignment of benefits before you sign it.
  • Ask about deposits and fees up front. Whether a deposit is needed depends on the job, so ask before work starts.
  • Ask for an itemized invoice with daily equipment counts.

See how we work and choosing a water damage company in Washington.

Common questions

Will I be charged if the inspection finds no water damage?

Ask before anyone comes out. Some companies charge a trip or inspection fee either way.

Will I be charged the full estimate if the job takes less work?

You shouldn't be. Drying equipment and labor should be billed for the days and hours actually used. Ask for the final invoice to match the drying log, not the first estimate.

I got a $6,700 invoice for water damage. Is that normal?

It may be. That's just above the national typical range for a whole job, and sewage or large losses run higher. Whether it's fair depends on the line items. Ask for the itemized invoice, the moisture readings and the equipment dates, then compare them.

What are containment, negative pressure and HEPA charges for?

Containment is plastic sheeting that keeps dust, mold or sewage contamination in the work area. Negative pressure means air is pulled out of that area, so air flows in, not out. A HEPA air scrubber filters the air inside. These are normal on sewage and mold jobs. On a small clean-water leak, ask why they're needed.

How does Xactimate track water mitigation equipment and readings?

Xactimate has a water mitigation log where crews record equipment and moisture readings by room and by day (Xactware). Ask your contractor for a copy of whatever drying log they keep.


Water in the house right now?

Shut off the main water valve, keep clear of wet outlets, and take photos before you move anything. Then call. Calls answered 24/7.

Call now